mirror of
https://gitlab.ewi.tudelft.nl/ee2l1/2025-2026/A.K.03.git
synced 2025-12-12 15:30:57 +01:00
67 lines
3.8 KiB
Plaintext
67 lines
3.8 KiB
Plaintext
{
|
|
"cells": [
|
|
{
|
|
"cell_type": "markdown",
|
|
"metadata": {},
|
|
"source": [
|
|
"# Appendix A: Programming the Audio Beacon\n",
|
|
"\n",
|
|
" This appendix describes the audio beacon signal parameters. The signal is generated by the M0 microcontroller of the LPC4357 ARM, an amplifier circuit (LM4752) and a loudspeaker. The microcontroller runs a dedicated program that produces continuously this signal on one of its PWM output pins which is amplified by an op-amp circuit and made audible by the loudspeaker.\n",
|
|
"\n",
|
|
"The generated signal is similar to the audio signals you have used in the EE2T11 Telecommunication A practicum (Labday 4). The parameters that define the signal can be set through the command interface; in contrast to the earlier practicum, now it is possible to use an arbitrary carrier frequency, bit frequency, and repetition count.\n",
|
|
"\n",
|
|
"## Audio Beacon signal parameters\n",
|
|
"\n",
|
|
"The audio beacon transmits a binary code sequence using ``on-off keying'' (OOK). If a bit in the sequence is 0, nothing is transmitted; if the bit is 1, a modulation carrier frequency is transmitted during a certain period. The number of bits is fixed at 32.\n",
|
|
"\n",
|
|
"Besides the actual bit sequence (a 32 bit code word), the parameters that determine the signal are:\n",
|
|
"\n",
|
|
"- Modulation carrier frequency (parameter *Freq0* specified in Hz), at most 30 kHz, although this is probably beyond the specs of the loudspeaker and microphones; \n",
|
|
"- Bit freqeuncy (parameter *Freq1* specified in Hz), this defines the rate at which the modulation carrier signal is switched on or off by bits in the code word, i.e., determines the duration of a single bit (and indirectly the bandwidth of the generated signal).\n",
|
|
"- Repetition count of the bit sequence (parameter *Count3*, an integer), this specifies the number of bits the beacon waits before transmitting the code again. The minimum value is 32 (otherwise a new code is transmitted before the previous one is finished). The resulting repetition frequency is, \n",
|
|
"\n",
|
|
"<p align=\"center\">\n",
|
|
" <img src=\"https://latex.codecogs.com/svg.latex?\\color{red}{repetition\\_frequency=\\frac{bit\\_frequency}{repetition\\_count}}\" alt=\"Equation\">\n",
|
|
"</p>\n",
|
|
"\n",
|
|
"For example, with a value of 5 kHz of the bit frequency, a repition count of 2500 gives a repetition count of 2500 gives a repetition freqeuncy of 2 kHz. You will probably want to have a higher repetition freqeuncy.\n",
|
|
"\n",
|
|
"[An example of pulses generated by the audio beacon](figaudiocode.pdf)\n",
|
|
"\n",
|
|
"\n",
|
|
"These parameters are set by sending them to the microcontroller on the car over the Bluetooth interface. The corresponding commands are described in *Controlling KITT* section in Module 1.\n",
|
|
"\n",
|
|
"The model *refsignal* that is used EE2T11 Telecommunications A practicum has similar parameters, but were limited to a specific set of values.\n",
|
|
"\n",
|
|
"The default setting of the audio beacon is a 32 bit code sequence bit-stream with:\n",
|
|
"\n",
|
|
"<center>\n",
|
|
"\n",
|
|
"| | | | | |\n",
|
|
"|-------|--------------------|---|-------------|----------|\n",
|
|
"| Freq0 | Carrier frequency | = | 15000 | Hz |\n",
|
|
"| Freq1 | Bit frequency | = | 5000 | Hz |\n",
|
|
"| Count3| Repeat counter | = | 64 | samples |\n",
|
|
"| | Code word | = | `0x92340f0f`| (hex) |\n",
|
|
"\n",
|
|
"</center>\n",
|
|
"\n",
|
|
"There is not guarantee at all this default setting is of high quality!\n",
|
|
"\n"
|
|
]
|
|
},
|
|
{
|
|
"cell_type": "markdown",
|
|
"metadata": {},
|
|
"source": []
|
|
}
|
|
],
|
|
"metadata": {
|
|
"language_info": {
|
|
"name": "python"
|
|
}
|
|
},
|
|
"nbformat": 4,
|
|
"nbformat_minor": 2
|
|
}
|